tech-sheet-36-32089301-0
Amana Technical Information Electric Range

DCF4205AC PDCF4205AC1 DCF4205AW PDCF4205AW1

Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit.

Refer to Service Manual RS2320006 for detailed installation, operating, testing, troubleshooting, and disassembly instructions.

Refer to Parts Manual RP2320099 for complete part number information.

! CAUTION

All safety information must be followed as provided in Service Manual RS2320006.

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.

Model DCF4205A* Model DCF4205A* Power Source @ 240 V / 208V Cooktop Surface Upswept X 9.5 KW Electrical rating 240 VAC ………. 7.3 KW Oversized glass ceramic Spillsaver 208 VAC ………. 40 Amp 60 Hz Frameless glass door with window X Amperage Interior oven light X Frequency 1,200 / * Two oven racks 6 positions X Element Wattage @ 240 V / 208V 2,000 / * Removable full width storage drawer X 6-inch ribbon radiant Electronic control with mylar overlay X 8-inch ribbon radiant Product Exterior Dimensions in. (cm) Height overall 47 (119) Oven Wattage @ 240 V / 208V 2,800 / * Width 30 (76) Bake 6 pass 3,000 / * Depth oven door closed with handle 28 13/16 (73) Broil 6 pass Clearance oven door 22 (56) 19 (48) Height of cooktop 36 (91) Oven Interior Dimensions in. (cm) 24 1/4 (61) Weight lbs. (kg) Height 19 (48) Approximately shipping weight 171 (78) Width Depth

* Rating of 208 VAC is approximately 80% of 240 VAC value.

October 2001 1 36-32089301-0

Component Testing Procedures

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.

Illustration Component Test Procedure Results 31823701 Oven light socket Remove one wire from receptacle Indicates continuity with bulb screwed in. and test resistance of terminals. 31722801 Measure voltage at oven light. 120 VAC, see wiring diagram for terminal 31938901 1200 W identification. 31939101 2000 W Oven indicator light Remove one lead from switch If no voltage is present at oven light, check 31926701 and terminal and measure resistance wiring or light switches. 31926702 Surface indicator light across terminals. Switch closed: 0 Measure voltage at indicator light. Switch open: Infinite resistance 32078201 31967101 Ribbon radiant Remove one wire lead from element If voltage is present and light does not elements, limiters are and measure resistance of the operate. Replace light. 31967302 not replaceable. element. If no voltage is present at indicator light check wiring. 31954301 Continuity, if not replace. 1200W: 44 to 49 Approximately 2000W: 26 to 30 Approximately

Verify supply voltage 240 VAC Remove wiring from terminals H1 Infinite switch and H2. Connect Volt ohms meter to Time On Time Off Control limit H1 and H2. 95% Bake element LO 5% 50% Measure the following for voltages at 0% LO, MED, HI: MED (4-5) 50%

H1 to H2 HI 100% Normally Closed Verify proper operation. 240 VAC, if not replace switch.

Closed ………. 215°F ………………….. Continuity Open ………… 245°F ………………….. Infinite If open at room temperature, replace. Disconnect wire leads to element and measure resistance of terminals. Continuity, approximately 20 , if not replace.

Broil element Measure voltage at bake element. 240 VAC, see wiring diagram for terminal identification. Disconnect wire leads to element If no voltage is present at bake element and measure resistance of terminals. check wiring.

Continuity, approximately 19 , if not replace.

Oven temperature Measure voltage at broil element. 240 VAC, see wiring diagram for terminal sensor Measure resistance. identification. If no voltage is present at broil element check wiring.

Approximately 1100 at room temperature 75°F.

31946302 Hinge Carefully open the door to full position. Slide hinge lock to lock position. ! CAUTION

Close the door to first stop position Do not place hands in hinge area when and raise door from hinge receivers. oven door is removed. Hinge can snap Hinge replacement requires door closed and pinch hands or fingers. disassembly.

36-32089301-0 2 October 2001

Component Testing Information

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.

Illustration Component Test Procedure Results 32040901 Auto latch assembly Motor switch 32088501 COM N.O. continuity Electronic range Unlocked ……………………………… COM N.O. open Mylar Overlay control Locked…………………………………. 32025902C Bisque Door switch COM N.C. continuity Door closed ………………………….. COM N.C. open Door open…………………………….. 120 VAC should be indicated, verifying Measure voltage at terminals voltage to control. J2 E7 (L1) and E2 (NEU) ……………

E5 J2 On power-up lock Relay drive requirements 240 VAC, if not replace control. light will blink for Bake BA to L2 ………………………… 240 VAC, if not replace control. E7 approximately 25 Broil BR to L2 ………………………… 75% bake element 25% broil element seconds, while Bake ………………………………………. 100% broil element E 3 control is verifying Broil ……………………………………….. lock latch position. Clean Time controlled 60 minutes 100% broil E4 Stage 1 …………………………………… 50% bake element and 50% broil element On power up, if Stage 2 …………………………………… 2 hours minimum to 4 hours maximum E2 sensor has failed. Time (Adjustable)……………………… No F – Code will be Verify voltage to control. displayed. Failure codes: If no voltage is present, check wiring. No oven functions F1-Control malfunction………………… If voltage is present, replace control. will start. E1

J1 F2-Oven over temperature…………… Check sensor resistance and wiring. PIN 1 Replace control if sensor and wiring are F3-Oven temperature sensor good. Open or Shorted ……………………. Check sensor resistance and wiring. Replace sensor, if wiring is good.

F9-Door latch circuit malfunction…… Check latch switch and associated wiring.

Temperature Calibration …………….. Turn oven control to OFF position. Press and hold both slew pads for 5 sec. Use slew pads to adjust temp setting. After 5 sec. of no input the mode is exited. Calibration will be retained through a power failure.

32025903W White

OVEN

COOK CLEAN OFF WM CLEAN T IME R BROIL TI ME ON OFF OVEN BAKE START LIGHT PUSH TO TURN RECALL PREHEAT LOCKED C O OK OVEN TEMP CLE AN CLO CK

October 2001 3 36-32089301-0

36-32089301-0 COLOR SURFACE ELEMENTS SURFACE ELEMENTS BK WH * GROUND GROUND STRAP Wiring Diagram and Schematic COLOR SYMBOL COULEUR L2 N STRAP NOT USED FOR L1 ! WARNING RD RED RD ROUGE SF2 RD RD FOUR WIRE To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless ORANGE OR ORANGE 1b 1b testing requires power. 1b SF2 1b INSTALLATIONS * GREEN OVEN LIGHT* OR YELLOW YL JAUNE 2b VT SF2 2b OR SF2 2b OR 2b VT SF2 WH or GREEN GN VERT BARE

BLUE BU BLEU 1a CHASSIS VIOLET 16 GA GROUND BLACK VT VIOLET 1a 1a 1a (FOUR WIRE BROWN 2a SF2 16GA 16 GA BK INSTALLATIONS GRAY 16GA BU BU ONLY) BK NOIR 2a SF2 2a SF2 2a SF2 WH YL YL TEMPERATURE BR MARRON 16GA BR BK/WH SENSOR

GY GRIS BR SF2

WHITE WH BLANC H2 H1 RD H2 H1 H2 H1 H2 H1 ERC GENESIS BU OR SF2 OR 6 SWITCH SWITCH SWITCH SWITCH L.R. OR AUX E1 R.F. R.R. L.F. L2 L1 P VT L2 L1 P OR L2 L1 P SF2 L2 L1 P SF2 VT RD 14GA RD VT WH M BU 5 MDL E4 WH/RD 14 or 16GA RD 14 or 16 COM1 GA RD

NO3 GY 14 or 16GA BK 14 or 16GA BK 14GA BK LATCH

DR LATCH VT RD L1-E7 COM 3 OR SW OR WH VT NO DRSW RIGHT NC COM 1 SURFACE WH NEU-E2 2 VT BROIL NO VT NC 2 NEON LEFT OVEN HIGH OR WH LIMIT 3000W BR BROIL E3 BU WH SURFACE BU OVEN DR WH/RD NEON 1 GY LT SW NC J1 MOTOR WH OR BAKE DOOR BU VT WH OR 2800W LKSW LOCK GY YL BAKE-E5 TEMPERATURE SENSOR J1 NEU AUX BU

6 E2 E1

6 2 5 WH VT PIN PIN CIR CIR 4 ERC GENESIS

2 1 LEFT

2 1 3 SURFACE

BU WH OR GY VT 2 E7 E4 E3 E5 WH VT NEON BA RIGHT 4 1 L1 MDL BR SURFACE 1b YL NEON 2b 6 5 4 3 21 16 1500W GA 1b RD BU BR 2b 1a RR 2a 6 5 4 3 21 14 16 2500W 1a BU WH GA GA 1b 1b RF 2a 2b 2b BU WH OR GY VT RD 2 2000W 1200W SOCKET WH 1a 1a CIR LR 2a LF 2a 16GA BK 150 °C BAKE NC OR YL ELEMENT BU OVEN HIGH H1 H2 H1 H2 H1 H2 H1 H2 * OVEN BROIL BU LIMIT LIGHT 18 or 20GA BR ELEMENT 16GA 14

* 14 GA GN GA CHASSIS GROUND 14 RD P L1 L2 P L1 L2 P L1 L2 P L1 L2 GA (NOTE 5) (N) BACKGUARD (NOTE 7) 150 °C GROUND BK WH * GROUND WH STRAP

NOTES: (L2) WHITE (L1) BLACK (N) RED 1. ALL INTERNAL WIRES ARE 18GA, 125°C XL UNLESS OTHERWISE NOTED. SF2 IS SEW-2/SF2 200°C RATED. MAIN TERMINAL 2. ALL REPLACEMENT WIRES MUST HAVE SAME RATING AS ORIGINAL WIRE. 3. SEE SERIAL PLATE FOR INPUT VOLTAGE/WATTAGE RATING. BLOCK 4. *DENOTES OPTIONAL EQUIPMENT AND RELATED WIRING NOT DIAGRAM SUPPLIED ON SOME MODELS. 35-32042801-0 5. ELEMENT WATTAGES VARY BY MODEL. REPLACEMENT ELEMENTS

MUST HAVE SAME WATTAGE AS ORIGINAL ELEMENTS. 6. FOR RANGE INSTALLATION, USE COPPER WIRE ONLY.

7. GROUND STRAP NOT USED FOR FOUR WIRE INSTALLATIONS.

October 2001 WARNING – ELECTRICAL SHOCK HAZARD DANGER -RISQUE DE CHOC ELECTRIQUE SCHEMATIC – DISCONNECT POWER AT MAIN -DEBRANCHER L’ALIMENTATION ELECTRIQUE. AVANT D’ENTRETENIR CETTE UNITE. 32042801 FUSE OR CIRCUIT BREAKER BEFORE SERVICING. RANGE CONDITIONS SHOWN: FAILURE TO DO SO COULD RESULT IN SERIOUS LE MANQUE DE RESPECT DE CETTE CONSIGNE POURRAIT ELEMENTS OFF AND AT ROOM TEMPERATURE. INJURY OR DEATH. AVOIR COMME RESULTAT UNE BLESSURE GRAVE OU MORTELLE. DOOR UNLATCHED AND CLOSED.