tech-sheet-16023431
24″ Front Load Washer Technical Information

MAH2400A*

Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit.

Refer to Service Manual 16023430 for detailed installation, operating, testing, troubleshooting, and disassembly instructions.

! CAUTION

All safety information must be followed as provided in Service Manual 16023430.

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power.

June 2006 1 16027174 RPL 16023431 ©2006 Maytag Services

Troubleshooting Procedures

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power.

Will Not Start Check belt.

Plug cord into live electrical outlet. Check for Washer with heat option does not tumble while

proper voltage. heating. (Export washers only)

Check fuse or reset circuit breaker. Will Not Spin Push the Start/Pause button to start the clothes Check to make sure the door is fully closed. Check for water left inside the washer. If present, washer. see Will Not Drain. Close door and push the Start/Pause button to Perform Board Output Test. Will washer spin? Possible unbalanced load scenario previously. start the clothes washer. Wash>Rinse>Spin Check for loose connections at machine control indicator LED should change from flashing board, pressure switch, motor, tach harness and (paused) to ‘ON’ continuously. motor control. Check to see if the washer is in a pause or soak Check belt. period in the cycle. Wait briefly and it may start. Check for restricted drain system. Check the line filter connection terminals for good

connections. No Water Fill Check the machine control board terminal Test water fill. Perform Board Output Test. Check to make sure water supply is turned on connections CN7 and CN5 for good connections. fully. Check for stuck buttons on console, pushing in on With no clothes in washer normal water level is between the 4th and 5th hole on the spinner back board tact switches. Readjust buttons on inside of wall. console. Replace machine control board.

Leaking Check electrical circuit and connections at the Make sure inlet hose connections are not leaking. water valve, and pressure switch. Check for rubber gasket damage due to over- tightening. Check for kinks in inlet hoses. Check standpipe for leak. Wrap a dry rag around Check for clogged inlet screens. the standpipe opening. If rag becomes wet, leak Visually check hot and cold separately for fill. is fault of home plumbing. Be sure the standpipe Check for low water pressure. May be dependent is capable of accepting the flow of water from the washer. on pressure entering home. Variations may occur Make sure end of drain hose is correctly inserted due to usage in the home at the time machine is and secured to drain standpipe. used. Check internal hose connections (fill, drain Check for frozen pipes and hoses. systems, dispenser hoses & clamps). Check resistance of water valve coils. (normal Check rubber boot. Remove, reposition and 1.18K ohms; CN3 connector – Cold (BU) – reinstall, if necessary. Bleach (OR) – Hot (RD) Check for possible kinked dispenser to outer tub Check for loose connections at the pressure switch or on the machine control board, connector CN4.

hose. Tub Full of Suds Hot water pressurization may force door open. Check for restricted drain system. See Will Not

No Tumble Drain and Will Not Spin. Start normal cycle with an empty machine and Check for loose wire connections at control board allow a fill to check tumble. Fabric cycles such as NORMAL, DELICATES, and pump. HAND WASH, & WRINKLE CONTROL only Perform Board Output Test. tumble periodically, every 60 seconds. Use high efficiency or low sudsing detergent Washer does not tumble during most fills or during presoak. specially formulated for front load washers. Perform Board Output Test. Reduce detergent amount for that specific load Check for loose connections at machine control board, pressure switch, motor, tach harness and size and soil level. Towel loads have a minimal motor control. amount of soil present and typically create more Check motor windings resistance. (Pins 8 & 9 = suds. 3.6 ohms, pins 1 & 10 = 1.1 ohms, Pins 5 & 10 = Check to see if belt is off motor and pulley. Run the clothes washer through another complete cycle using the coldest water, tablespoon of salt and no detergent.

1.1 ohms)

16027174 2 June 2006

RPL 16023431 ©2006 Maytag Services

Troubleshooting Procedures

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power.

Wet Clothes Make sure water heater is set to deliver a Very small clothes loads can cause unbalanced minimum of 120°F (49°C) hot water at the tap. loads. Add additional towels. Also check water heater capacity and recovery Excessive suds may have been present, due to rate. not using High-Efficiency detergent. Reduce amount of detergent usage. If the water heater is located a long distance See Will Not Spin. from washer, the water line may need to be “Low” Spin Speed was selected. purged prior to starting wash cycle.

Will Not Lock Too Hot/Too Cold: This washer uses a reduced Door not all the way closed or not properly amount of water, while the control board meters aligned. Possible laundry load is too large to the incoming flow to regulate the actual close door. temperature of the water in the tub. This may Place washer into Service Mode and check for appear to be significantly warmer/cooler than diagnostic codes 4 &18. expected. Perform Board Output Test. Check door lock system. Make sure the temperature selection is correct. Check electrical connections at lock switch Disconnect inlet hoses from the Water Valve assembly and machine control board (CN2). and clean the valve screens of any debris. Will Not Unlock Push door closed to make sure nothing from Noisy and/or Vibration/Walking inside is pressing against it, which may keep it Check if the washer was properly leveled and from unlocking. the locking nuts are securely tightened up Display shows “L0”. Press Power Off, against the base frame of the washer. Start/Pause or unplug washer. Door will unlock Check and determine all five of the shipping after 3 minutes. bolts and spacers have been fully removed Door locked from water level too high. Opening from the rear panel of the washer. door will result in water draining from door Check for proper load size and distribution. If opening. clothes load is too small, add a few towels to Place washer into Service Mode. balance the clothes load better. Perform Board Output Test. Check door lock Check the tightness of the rear pulley bolt. system for loose connections. Tighten if necessary. Clean floor and bottom side of washer feet.

Rubber Feet Leaving Marks on Floor Use a pencil eraser to remove mark. Walk washer into location, do not drag.

Will Not Drain Additive Cups Full of Water Check for restricted drain system. Small amount of water in bottom of additive In cold climates check for frozen drain hose. cups is normal. Check for 120 VAC at the pump when a spin Remove and wash Dispenser Tray, removable cycle is selected. Cup, and Rinse Cap. Check pump motor winding resistance. (14.2 Level washer. ohms) Check that the machine control correctly Buttons do not Respond senses the water level in the washer. See Options cannot be changed while cycle is Board Input Test. running. Press Start/Pause once to pause Go to Board Output Test and perform Pump cycle while making selections. Press Out Test. Start/Pause again to restart washer. Check the machine control board connections Child Lock feature has been selected. To at CN3 (Pin 1) for the pump. Should see 110- disable feature press and hold Chime and 120VAC. Delay Start simultaneously until a beep is Check tub to pump hose for twist in hose. heard. When display shows “End”, only the Power Off Wrong Water Temperature button will function. Press Power Off and make Check that both faucets are turned on fully. new cycle selections.

June 2006 3 16027174 RPL 16023431 ©2006 Maytag Services

Troubleshooting Procedures

! WARNING

To avoid risk of electrical shock, personal injury, or death; disconnect power to washer before servicing, unless testing requires power.

Consumer Information Codes Service Mode If the consumer observes codes on display, see table below. Service Mode enables service personnel to verify the operation of the washing machine and diagnose LED Description problems. Service Mode can be entered in the middle Display of any wash cycle without interrupting the cycle. While in Service Mode, the technician can cancel the current Distribute Clothes: The load is cycle, set a continuous running mode, start a variety of special service tests and view diagnostic displays. dc unbalanced, preventing high-speed spin. Redistribute clothes. See

Diagnostic Code 10.

nd No Drain: The machine has tried to Enter / Exit Service Mode

drain. To enter Service Mode press the Spin and Temperature keys for three seconds or until the control Open the Door: The door has not beeps.

od been opened for the last three NOTE: The washer must be ‘ON’ before Service Mode can be entered. completed cycles. The motor speed will be displayed when started (motor nF No fill: the machine has tried to fill. not running display will be 0). The present state of the machine will not be changed (i.e., the current cycle in See No Water Fill. progress will not be interrupted and only the display will change). All LED’s will be turned ‘OFF’ except the “Door dL Latch Unlocked: Close door tightly Lock” LED. It will continue to display the condition of to enable locking. the door lock.

LE Water fill error. Go to fill test. To exit: 1) Press Spin and Temperature keys for 3 seconds again, or 2) press Power Off, or 3) unplug the Sump thermistor failure. Check for machine. Pressing the Start/Pause button while running a test will pause the individual test, while tE loose wires. Replace sump remaining in Service Mode.

thermistor. Access Service Tests and Diagnostic Features while in Service Mode. Drive system is not working The following table summarizes special tests and 3E correctly. Bad windings, speed features available in Service Mode, along with methods sensor, wiring connections, or of activation and cancellation.

Control Board.

LO The door will not unlock after 3 attempts.

FL The washer failed to lock the door. after 3 attempts.

A fault is detected in the water level

OE sensor. Data (frequency) shows the Test or Display water level is at or above the Press LED to Press LED to overflow level. Start Cancel

Quick Spin Press Delay Press Delay start and Test Start and Temperature Press Power Temperature Off (exits Service Mode) Hold Quick Press Start Spin Step Pause (during Press Delay (holds test) Start and predefined Temperature RPM) (cancels hold & resumes next step)

16027174 4 June 2006 RPL 16023431 ©2006 Maytag Services

Troubleshooting Procedures

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power.

Test or Display Press LED to Press LED to Test or Display Press LED to Press LED to Start Cancel Start Cancel Fast All Diagnostic Time- Press Spin to Press Spin Codes Rotate Cycle N/A Down / start test. Press Cycle Count Selector either Advance Start/Pause Press Power No. for direction Release to Next during cycle to Off (also exits Diagnostic Start/Pause Step advance. Service Mode) Code Press and hold (returns to Press Delay Start/Pause in diagnostic code # Quick Press Start and Clear All center of cycle display) Service Temperature Chime to Diagnostic selector knob, Cycle and Soil Level resume Codes while diagnostic Press Soil Hold Quick Press Power code is Level a 3rd time Service Cycle Press Delay Off twice after Display displayed Step Start and starting test Software Chime together Version Press Delay Press Start + Soil LED/Switch Press Delay Temperature Cycle Count Level together Test Start (then Press while displaying individual Temperature diagnostic buttons to test) and Extra codes Rotate Cycle Rinse Selector Press Chime Press Soil clockwise, the again Level. Press 2 LED’s around it times for will be toggled. displays with Rotate counter only 2 character clockwise, the positions. 7-segment LED’s toggle. Press Extra Press Rinse Start/Pause button inside Quick Spin Test the “Rotary While in Service Mode, press Delay Start and Cycle Selector, Temperature keys to start a Quick Spin Test. all of the LED’s Quick Spin test steps are as follows: around the 1) Lock the door. Rotary Cycle 2) Spin clockwise and stop. Selector will be 3) Spin counterclockwise and stop. toggled. 4) Spin counterclockwise, start Drain Pump and spin to maximum RPM. Hold for 25 seconds. IN Board Press 5) Coast down, stop and turn ‘OFF’ Drain Pump. 6) Unlock Door after 60 seconds. Beeps once. Input Temperature Hold Quick Spin Step Test If the Start Pause key is pressed during the Quick Spin test, the machine will hold at the Board Press current speed for up to 10 minutes. At the end Output Temperature of 10 minutes, the machine will resume and Test / and Extra finish the Quick Spin test. To cancel the Hold System Check Rinse and allow the Spin Test to continue, press the Delay Start and Temperature keys. Press Chime – Diagnostic 1st code Code Display displays (Initial)

June 2006 5 16027174

©2006 Maytag Services RPL 16023431

Troubleshooting Procedures

! WARNING

To avoid risk of electrical shock, personal injury, or death; disconnect power to washer before servicing, unless testing requires power.

¤ Fast Time Down Test 9. Unlock the door when the RPM is zero. While any test or cycle is running in Service Mode, pressing the Spin key will The “SC” in the display will blink as an indication of start the fast time down test. Pressing the failure, and continue blinking until the quick service Start/Pause will advance the program to cycle test has reached the end. Any diagnostic code the next cycle stage. logged during this test will result in failure of the test, but will not necessarily stop the test. Cycle stages are located at key locations in the machine operation. As the program is advanced it During the Quick Service Cycle, pressing the Chime will index as follows: The end of each fill (the same key will advance to the next step. Pressing the Delay as the beginning of a tumble session for Wash, or Start and Chime keys will suspend the machine at the Rinse); at the beginning of a drain session; at the current step for up to 30 minutes or until Delay Start beginning of a spin session (at this position, check and Chime are pressed again. All LEDs should flash the water level, if over reset level, drain first before ‘ON’ and ‘OFF’ while the system is suspended or on entering the spin function); at the beginning of a fill hold. session; at the beginning of Bleach fill; at the beginning of Fabric Softener fill; and every 3 LED/Switch Test minutes during the tumble sessions (Wash, and While in Service Mode, press and hold the Rinses). Delay Start key to start a LED/Switch check. All the LEDs can be toggled or slewed by pressing the key # Quick Service Cycle associated with the LED or set of LEDs. Each time the While in Service Mode, pressing the Rotary Cycle Selector is rotated clockwise, the LED’s Temperature and Soil Level key for 3 around it will be toggled in a clockwise motion. If the seconds will start a Quick Service Cycle. Rotary Cycle Selector is rotated counter clockwise, This will be a quick check of all systems. If display the 7-segment LED’s toggle. If the Start/Pause button shows od then open and close door. Pressing Chime inside the Rotary Cycle Selector is pressed, all of the will advance to the next cycle. LED’s around the Rotary Cycle Selector will be toggled. The following steps are performed: Display shows “sc”. All keys (including the Power Off button) must be 1. Lock door and pump starts. pressed within 5 minutes for this test to pass. “PA” will 2. Hot water for 5 seconds and then turn ‘OFF’. be displayed for five (5) seconds once all keys have 3. Cold water for 5 seconds and then turn ‘OFF’. been pressed and the test is completed. Following 20 4. Bleach valve for 5 seconds and then turn ‘OFF’. seconds of inactivity at any point, this test will exit 5. Dispense softener using cold water and bleach without any display. The Power Off switch pad must be pressed twice within 30 seconds to cancel this test. water for 5 seconds and then turn ‘OFF’. 6. Turn ‘ON’ Hot and Cold valves until the control Switch Action

detects proper water level. During this time, tumble Delay Start Press once at 45 rpm for 5 seconds in a clockwise direction, Chime Press once pause for 2 seconds, tumble at 45 rpm for 5 Extra Rinse Press once seconds in a counterclockwise direction, pause for Soil Level Press 4 times 2 seconds. Continue pattern until the water level is Spin Press 5 times detected. Minimum time for this segment to be 5 Temperature Press 6 times seconds. After water height is achieved, continue Selector Knob Rotate 1 full revolution clockwise tumble pattern for another 14 seconds. If the Selector Knob 1 position counterclockwise washer is equipped, turn ‘ON’ heater for first 5 Start Pause Press once seconds of this tumble pattern. Advance the Power Off Press once washer to next step if water is not connected to machine. 7. Drain and spin to maximum speed. Machine will achieve maximum speed using the safest, fastest method. 8. Display a “PA” (Passed) continuously for 5 seconds if no diagnostic codes were logged during the test. Washer will return to the normal Service Mode at the end of the 10 second period.

16027174 6 June 2006 RPL 16023431 ©2006 Maytag Services

Troubleshooting Procedures

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power.

Board Input Test While in Service Mode follow chart to check respective function.

IN While in Service Mode, pressing the Selection Component Function

Temperature key will begin the Board

Input Test. This test turns ‘ON’ a specified Rotary Cycle Selector Off To On Set To Heavy Duty or output after a key press. Pressing the Press Start Pause Main Relay On To Off Temperature key again cancels the test. (Display Rotary Cycle Selector Hot Water Set To Normal Valve Valve On shows in). Press Start Pause 2nd Press Cold Water Valve Off While in Service Mode follow chart to check respective Rotary Cycle Selector Valve function. Set To Wrinkle Control Valve On Press Start Pause 2nd Press Selection Function Display Valve Off

Rotary Cycle Selector Lock State UL or LO Rotary Cycle Selector Bleach Valve Valve On Set To Normal Set To Delicates Drain Pump 2nd Press Press Start Pause Degrees F Press Start Pause Valve Off

Rotary Cycle Selector High Water Rotary Cycle Selector Pump On Set To Wrinkle Control Level Set To Quick Wash 2nd Press Press Start Pause Press Start Pause Pump Off

Rotary Cycle Selector Press Delay Start Motor Motor On Set To Colors Press Start Pause Low Water * 2nd Press Level Motor Off Press Chime Door Lock 1 Attempt To Unlock

Rotary Cycle Selector *Tub Balance Press Temperature Door Lock Lock Door Set To Hand Wash Press Start Pause Fabric Softener Fill 2nd Press Valves Off Press Delay Start Water Extra Rinse Bleach Valve Temperature and

Cold Water Valve

Rotary Cycle Selector Water Degrees C *Note: Function may not occur for up to 20 seconds. Set To Delicates Temperature The “Delay Start” LED is ‘ON’. When activated, Press Start Pause the machine will tumble for 5 seconds in the CW direction, pause for 2 seconds, tumble in the * “U0” will be displayed during the time when the CCW direction for 5 seconds, pause for 2 machine is correcting for the unbalance; e.g. slowing seconds; repeating this pattern until the Delay down to redistribute the load or to get to a lower spin Start button is pressed again. All tumble speeds speed. Once the situation has been corrected (i.e. the are 45 rpm. load has begun tumbling or the lower speed has resulted in an acceptable amount of unbalance) “U0” Display Diagnostic Codes will be displayed again. The diagnostic code display can be toggled ‘ON’ and ‘OFF’ from Service Board Output Test Mode by pressing the Chime key and rotating the cycle select knob. The While in Service Mode, pressing the display will show a “d”. Temperature and Extra Rinse key will begin the Board Output Test. This test turns ‘ON’ a Rotating the Cycle Selector knob in either direction will specified output after a key press. (Pressing the Temperature and Extra Rinse key again cancels the cycle through the list of codes one code at a time with test.) Only one output can be ‘ON’ at any time. All outputs will be turned ‘OFF’ after five (5) minutes of no wrap. Once an initial direction is selected by the user inactivity. (either Clockwise or Counterclockwise), subsequent

movements of the knob in the same direction will show

older codes. If the user changes direction and turns the

knob in the opposite direction, the more recent code will

be displayed. If rotation is continued to the limits of the

June 2006 7 16027174

©2006 Maytag Services RPL 16023431

Troubleshooting Procedures

! WARNING

To avoid risk of electrical shock, personal injury, or death; disconnect power to washer before servicing, unless testing requires power.

list, the display will remain at the top or the end of the Diag. Description Trigger Action to be Code taken list. A pair of dashes “- -” will be displayed at the end 9 Not Used of the list of diagnostic codes. If the user navigates up the list of codes, when the control reaches the top, it will Never again show “d”. Unbalance exceeded 400 A code generated during the current cycle will be displayed with the Spin Indicator LED turned ‘ON’. If no detected rpm due to an cycle is currently running, a code generated during the previous cycle will be displayed with the Spin Indicator during final unbalanced LED – Will display LED turned ‘ON’. spin, which load. If “dc” Access Other Features 10 prevented detected, Go to “Machine While a diagnostic code is displayed, if the Start Pause button on the rotary cycle selector knob is pressed and the spinner washer will Control Board held, the machine will display the number of cycles since the diagnostic code occurred. To clear the from pause and Output Test”. diagnostic list, press the Delay Start and Soil Level keys for 3 seconds while viewing the list. exceeding alert user to

400 rpm. redistribute

the load.

Go to “Clear

diagnostic codes”

Disconnect and

Diagnostic Codes 11 Will not Difficulty in reconnect the remember reading washer power cord Diag. Description Trigger Action to be machine memory. Code No Drain taken settings. at power supply The water outlet. 1 level fails to Displays “nd” drop below Go to “Will Not If condition still

the Low Drain” exists, replace Water level Troubleshooting reset within machine control 15 minutes, Section before a spin board.

begins. 12-17 Not Used

Check for loose

wire connections

Clear the diagnostic

Not Used Detected code and recheck;

2 door lock Open door if reoccurs, perform

Continuous fill 18 switch open lock switch Diagnostic of 12 minutes. during cycle with motor Motor/Machine Total fill of 20 Displays “nF” 3 No Fill Go to “No Water when not running. Control Board test minutes. Fill”. expected. Check for faulty

motor relay on the

Not Used machine control

4-7 board.

Input signal

from water

level Sensor

8 Water level is out of Displays “LE” sensor fault. range, Go to “No Water Washer will Fill”.

beep and

pause the

wash cycle.

16027174 8 June 2006 RPL 16023431 ©2006 Maytag Services

Troubleshooting Procedures

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power.

Diag. Description Trigger Action to be Diag. Description Trigger Action to be Code Code taken taken E 29 Displays ” tE”. Water level in Sump Abnormal – Loose or pinched thermistor high/low temp the machine wires failure or ohm – Bad sump is believed to (Optional) resistance thermistor

be above the seen

overflow level.

When this

condition is First check to see 30-39 Not Used

Water detected, the that water valve is

sensor level machine will not stuck. If water Displays “3E”.

fault. automatically valve is OK, check Motor speed Check the motor

begin water level sensor. 3E Motor failure indicator windings, the speed error. Motor sensor, wiring pumping

water out of won’t turn. connections, or

the machine Control Board.

until it falls

below the 40-92 Not Used

overflow level. Exit Service Mode To exit: 1) Press Spin and Temperature keys for 3 19-24 Not Used seconds again, or 2) press Power Off, or 3) unplug the machine. After five (5) minutes of inactivity (user key Tach signal presses) in Service Mode, the machine will exit the Service Mode and resume normal operations. Pressing exists without the Power Off key will completely exit Service Mode. If a cycle is running, cancel the cycle. Pressing the Motor tach torque Start/Pause key while running a test will pause the individual test, while remaining in Service Mode. A signal exists commanded Displays “bE”. power loss during Service Mode will cancel this mode.

25 without or when not Replace motor

motor expected. control board.

running. (Abnormal

condition

only).

26-28 Not Used

June 2006 9 16027174 RPL 16023431 ©2006 Maytag Services

Troubleshooting Procedures

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless testing requires power.

Component Diagnostics NOTE: For ohm checks unplug harness connector on console and test from wire insertion side of the harness

connectors.

Main

DRAIN PUMP 5 4 3 2 1 CN4 1 22 Tub Sump

Thermistor/ Pressure SW

1 432 1 Yellow wire Pin 3 on CN4 to Pink wire Pin 4 (5V+DC or approx 12,000 ohms) CN3

Blue wire Pin 2 on CN6 to Gray wire Pin 1 on CN3 120V or approx 16 ohms

WATER VALVE

2

8

1

432 1

CN3 MAIN

(Hot Valve) Red wire Pin 4 on CN3 to White wire Pin 1 on Main. Approx 11,000 ohms or 120 volts.

(Bleach Valve) Orange wire Pin 3 on CN3 to Whitewire Pin 1 on Main. Approx 11,000 or 120 volts.

(Cold Valve) Blue wire Pin 2 on CN3 to White wire Pin 1 on Main. Approx 11,000 ohms or 120 volts.

16027174 10 June 2006 RPL 16023431 ©2006 Maytag Services

Component Testing Procedures

! WARNING

To avoid risk of electrical shock, personal injury, or death; disconnect power to washer before servicing, unless testing requires power.

Motor windings

6 5 4

3 2 1

CN1

(CN1) Unplug connector and test Resistance. 12 3 5 7 Rotor Orange Pin 1 to Gray Pin 3 = approx 3.65 ohms. 4 6 8 Stator Yellow Pin 5 to Violet Pin 4 = approx 1.1 ohms. 9 Stator Yellow Pin 5 to Blue Pin 6 = approx 1.1 ohms. 10

Cycle Chart

Wash Rinse 1 Rinse 2 Spin Final Cycle Temp Drain Fill/Tumble Soak Wash Loose Sub Midterm Fill/Tumble Rinse Loose/Anti- Sub Drain Midterm Fill/Tumble Rinse Loose/Anti- Sub Drain Spin Loose Sub Total Heavy Duty /Cool Total Drain Spin suds Fill Total Spin suds Fill Total Total (minutes) W/C 2 Normal W/W (1) (2) 3 34 1 41 (1) (4) (2) 4 2 11 (1) (4) (2) 4 2 11 (1) (6) (1) 8 71 H/C(N) 2 71 Wrinkle C/C(N) (1) (2) 3 34 1 41 (1) (4) (2) 4 2 11 (1) (4) (2) 4 2 11 (1) (6) (1) 8 71 Control C/C 2 55 W/C (1) (2) 3 34 1 41 (1) (4) (2) 4 2 11 (1) (4) (2) 4 2 11 (1) (6) (1) 8 55 Colors W/W 2 55 H/C(N) (1) (2) 3 18 1 25 (1) (4) (2) 4 2 11 (1) (4) (2) 4 2 11 (1) (6) (1) 8 55 Delicate C/C(N) 2 55 Handwash C/C (1) (2) 3 18 1 25 (1) (4) (2) 4 2 11 (1) (4) (2) 4 2 11 (1) (6) (1) 8 45 W/C 2 45 Quick Wash W/W (1) (2) 3 18 1 25 (1) (4) (2) 4 2 11 (1) (4) (2) 4 2 11 (1) (6) (1) 8 45 Drain H/C(N) 2 45 Spin C/C(N) (1) (2) 3 18 1 25 (1) (4) (2) 4 2 11 (1) (4) (2) 4 2 11 (1) (6) (1) 8 45 C/C 2 53 Rinse & Spin W/C (1) (2) 3 18 1 25 (1) (4) (2) 4 2 11 (1) (4) (2) 4 2 11 (1) (6) (1) 8 53 W/W 2 53 H/C(N) (1) (2) 3 16 1 23 (1) – (2) 4 2 7 (1) – (2) 4 2 7 (1) (6) (1) 8 53 C/C(N) 2 53 C/C (1) (2) 3 16 1 23 (1) – (2) 4 2 7 (1) – (2) 4 2 7 (1) (6) (1) 8 45 W/C 2 45 W/W (1) (2) 3 16 1 23 (1) – (2) 4 2 7 (1) – (2) 4 2 7 (1) (6) (1) 8 45 C/C(N) 2 45 C/C (1) (2) 3 16 1 23 (1) – (2) 4 2 7 (1) – (2) 4 2 7 (1) (6) (1) 8 43 W/C 2 43 W/W (1) (2) 3 16 1 23 (1) – (2) 4 2 7 (1) – (2) 4 2 7 (1) (6) (1) 8 43 C/C(N) 2 43 C/C (1) (2) 3 16 1 23 (1) (4) (2) 4 2 11 (1) (4) (2) 4 2 11 (1) (6) (1) 8 29 W/C 2 29 W/W (1) (2) 3 16 1 23 (1) (4) (2) 4 2 11 (1) (4) (2) 4 2 11 (1) (6) (1) 8 29 H/C(N) 2 29 (1) (2) 3 16 1 23 (1) (4) (2) 4 2 11 (1) (4) (2) 4 – 11 (1) (6) (1) 8 29 – – 1 – (1) (2) 3 16 1 23 (1) (4) (2) 4 2 11 (1) (4) (2) 4 – 11 (1) (6) (1) 8 8 C/C(N) – 15 C/C (1) (2) 3 16 1 23 (1) (4) (2) 4 2 11 (1) (4) (2) 4 – 11 (1) (6) (1) 8 15 W/C – 15 W/W (1) (2) – 10 – 13 (1) (4) (2) 5 2 12 (1) (4) (2) 5 – 12 (1) (6) (1) 8 15 H/C(N) 15 (1) (2) – 10 – 13 (1) (4) (2) 5 2 12 (1) (4) (2) 5 12 (1) (6) (1) 8

(1) (2) – 10 – 13 (1) (4) (2) 5 2 12 (1) (4) (2) 5 12 (1) (6) (1) 8

(1) (2) – 10 – 13 (1) (4) (2) 5 2 12 (1) (4) (2) 5 12 (1) (6) (1) 8

(1) (2) – 8 – 11 (1) (4) (2) 5 2 12 (1) (4) (2) 5 12 (1) (6) (1) 8

(1) (2) – 8 – 11 (1) (4) (2) 5 2 12 (1) (4) (2) 5 12 (1) (6) (1) 8

(1) (2) – 8 – 11 (1) (4) (2) 5 2 12 (1) (4) (2) 5 12 (1) (6) (1) 8

(1) (2) – 8 – 11 (1) (4) (2) 5 2 12 (1) (4) (2) 5 12 (1) (6) (1) 8

(1) (2) 3 4 1 11 (1) – (2) 2 2 5 (1) – (2) 2 5 (1) (6) (1) 8

(1) (2) 3 4 1 11 (1) – (2) 2 2 5 (1) – (2) 2 5 (1) (6) (1) 8

(1) (2) 3 4 1 11 (1) – (2) 2 2 5 (1) – (2) 2 5 (1) (6) (1) 8

(1) (2) 3 4 1 11 (1) – (2) 2 2 5 (1) – (2) 2 5 (1) (6) (1) 8

(1) (2) 3 4 1 11 (1) – (2) 2 2 5 (1) – (2) 2 5 (1) (6) (1) 8

– – – – – – – – – – – – – – (1) – – 1

– – – – – – – – – – – – – – (1) (6) (1) 8

– – – – – (1) – (2) 4 2 7 – – – – (1) (6) (1) 8

– – – – – (1) – (2) 4 2 7 – – – – (1) (6) (1) 8

– – – – – (1) – (2) 4 2 7 – – – – (1) (6) (1) 8

– – – – – (1) – (2) 4 2 7 – – – – (1) (6) (1) 8

– – – – – (1) – (2) 4 2 7 – – – – (1) (6) (1) 8

June 2006 11 16027174 RPL 16023431 ©2006 Maytag Services

Wiring Diagram

! WARNING

To avoid risk of electrical shock, personal injury, or death; disconnect power to washer before servicing, unless testing requires power.

CN8 CN6 CN1 CN7 CN5 CN3 CN4 CN2

16027174 12 June 2006 RPL 16023431 ©2006 Maytag Services