[pdf-embedder url=’http://appliancetechmanuals.com/wp-content/uploads/whirlpool/tech-sheet-16022362.pdf’ title=’tech-sheet-16022362′]Amana Technical Information Electric Range

ACF7225AB ACF7225AC ACF7225AW

Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit.

Refer to Service Manual RS2320006 for detailed installation, operating, testing, troubleshooting, and disassembly instructions.

! CAUTION

All safety information must be followed as provided in Service Manual RS2320006.

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.

Model ACF7225A* Model ACF7225A* Power Source @ 240 V / 208 V Cooktop Surface Upswept 10.3 KW X Electrical rating 240 VAC ………. 7.8 KW Oversized glass ceramic Spillsaver 208 VAC ………. 40 Amp X 60 Hz Frameless glass door with window X Amperage Interior oven light X Frequency 1,200 / * Watts Two oven racks 6 positions X Element Wattage @ 240 V 1,500 / * Watts Removable full width storage drawer X 6-inch ribbon radiant 2,000 / * Watts Electronic range control ERC 7-inch ribbon radiant 2,500 / * Watts 47 (119) 8-inch ribbon radiant Product Exterior Dimensions in. (cm) 30 (76) 9-inch ribbon radiant 2,800 / * Watts Height overall 28 13/16 (73) Oven Wattage @ 240 V 3,000 / * Watts Width 22 (56) Bake 6 pass Depth oven door closed with handle 36 (91) Broil 6 pass 19 (48) Clearance oven door Oven Interior Dimensions in. (cm) 24 1/4 (61) Height of cooktop 171 (78) Height 19 (48) Width Weight lbs. (kg) Depth Approximately shipping weight

* Rating of 208 VAC is approximately 80% of 240 VAC value.

June 2003 1 MFG #: 36 32117001 0

Service #: 16022362

Component Testing Procedures

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.

Illustration Component Test Procedure Results Oven light socket Remove one wire from receptacle Indicates continuity with bulb screwed in. 1200 W and test resistance of terminals. 1500 W 2000 W Oven indicator light Measure voltage at oven light. 120 VAC, see wiring diagram for terminal 2500 W and identification. Surface indicator light Remove one lead from light terminal If no voltage is present at oven light, and measure resistance across check wiring or light switches. Ribbon radiant terminals. elements, limiters are Measure voltage at indicator light. Switch closed: 0 not replaceable. Switch open: Infinite resistance Remove one wire lead from element Infinite switch and measure resistance of the If voltage is present and light does not element. Control limit operate. Replace light. Verify supply voltage Bake element Remove wiring from terminals H1 and If no voltage is present at indicator light H2. Connect Volt ohms meter to H1 and H2. check wiring.

Measure the following for voltages at Continuity, if not replace. LO, MED, HI: 1200W: 44 to 49 Approximately H1 to H2 Normally Closed 1500W: 36 to 40 Approximately Verify proper operation. 2000W: 26 to 30 Approximately Closed ………… 215°F………………….. Open ………….. 245°F………………….. 2500W: 20 to 23 Approximately Disconnect wire leads to element and measure resistance of terminals. 240 VAC

Time On Time Off

LO 5% 95%

MED (4-5) 50% 50%

HI 100% 0%

240 VAC, if not replace switch. If open at room temperature, replace.

Continuity Infinite Continuity, approximately 20 , if not replace.

Broil element Measure voltage at bake element. 240 VAC, see wiring diagram for terminal identification. Disconnect wire leads to element and If no voltage is present at bake element measure resistance of terminals. check wiring.

Continuity, approximately 19 , if not replace.

Oven temperature Measure voltage at broil element. 240 VAC, see wiring diagram for terminal sensor Measure resistance. identification. If no voltage is present at broil element check wiring.

Approximately 1100 at room temperature 75°F.

Convection motor fan Verify supply voltage…………………………. 120 VAC and blade Remove wires from terminals: Rocker switch Check continuity of terminals and verify terminals are not shorted to chassis…….. Continuity

Terminal to chassis …………………………… No continuity Measure continuity of switch positions: Continuity, if not replace. Closed Infinite, if not replace. Open

MFG #: 36 32117001 0 2 June 2003

Service #: 16022362

Component Testing Information

! WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.

Illustration Component Test Procedure Results Auto latch assembly Motor switch Mylar Overlay COM N.O. continuity Black/Stainless Steel Electronic range Unlocked………………………………. COM N.O. open control Locked …………………………………. Door switch COM N.C. continuity Door closed ………………………….. COM N.C. open Door open…………………………….. 120 VAC should be indicated, verifying Measure voltage at terminals voltage to control. J2 E7 (L1) and E2 (NEU) ……………

E7 J2E5 On power-up lock Relay drive requirements 240 VAC, if not replace control. light will blink for Bake BA to L2…………………………. 240 VAC, if not replace control. E3 approximately 25 Broil BR to L2 ………………………… 75% bake element 25% broil element seconds, while control Bake ………………………………………. 100% broil element E4 is verifying lock latch Broil ……………………………………….. position. Clean Time controlled 60 minutes 100% broil E2 Stage 1 …………………………………… 50% bake element and 50% broil element On power up, if Stage 2 …………………………………… 2 hours minimum to 4 hours maximum sensor has failed. Time (Adjustable)……………………… No F – Code will be Verify voltage to control. displayed. Failure codes: If no voltage is present, check wiring. No oven functions will F1-Control malfunction………………… If voltage is present, replace control. start. E1

J1 F2-Oven over temperature…………… Check sensor resistance and wiring. PIN 1 Replace control if sensor and wiring are F3-Oven temperature sensor good. Open or Shorted ……………………. Check sensor resistance and wiring. Replace sensor, if wiring is good.

F9-Door latch circuit malfunction…… Check latch switch and associated wiring.

Temperature Calibration……………… Turn oven control to OFF position. Press and hold both slew pads for 5 sec. Use slew pads to adjust temp setting. After 5 sec. of no input the mode is exited. Calibration will be retained through a power failure.

Bisque White

OVEN

COOK CLEAN OFF WM C LEAN TIMER TIME ON OFF

BROIL

RECALL START CONVECTION BAKE PREHEAT LOCKED PUSH TO TURN OVEN TEMP CO OK CLOCK CLE AN

June 2003 3 MFG #: 36 32117001 0

Service #: 16022362

Service #: 16022362 MFG #: 36 32117001 0 COLOR SURFACE ELEMENTS SURFACE ELEMENTS BK WH *GROUND GROUND STRAP Wiring Diagram and Schematic COLOR SYMBOL COULEUR L2 N NOT USED FOR STRAP ! WARNING RED RD ROUGE SF2 RD RD L1 RD To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless ORANGE OR ORANGE 1b 1b 1b SF2 1b FOUR WIRE testing requires power. JAUNE YELLOW YL 2b VT SF2 2b OR SF2 2b OR 2b VT SF2 INSTALLATIONS * OVEN * GREEN VERT GREEN GN BLEU BK OR LIGHT WH or OR BARE BLUE BU 1a VIOLET VT VIOLET 1a 16 GA 1a 1a CHASSIS 16GA 16 GA BK GROUND BLACK BK NOIR 2a 16GA 2a SF2 OVEN LT (FOUR WIRE 16GA SF2 BU BU 2a SF2 2a SF2 WH SWITCH INSTALLATIONS BROWN BR MARRON BR SF2 YL YL ONLY) GRAY GY GRIS BR BK/WH WHITE WH TEMPERATURE BLANC H2 H1 RD H2 H1 H2 H1 H2 H1 SENSOR SF2 BK SWITCH SWITCH SWITCH OR SWITCH BU L.R. SF2 L.F. 6 OR R.F. R.R. OR WH M OR ERC GENESIS/CONV L2 L1 P VT L2 L1 P L2 L1 P L2 L1 P 14 or 16 SF2 GA RD VT RD AUX E1 14 or 16GA RD OVEN OR 14GA RD VT CONV FAN

LIGHT COM1 GY 14 or 16GA BK 14 or 16GA BK 14GA BK WH M BU MDL E4 5 SWITCH NO3 WH/RD VT LATCH 3 OR DR LATCH RIGHT WH VT DRSW SW COM OR SURFACE RD L1-E7

COM 1 WH NEON LEFT VT NC 2 WH SURFACE WH CONV OR WH NEU-E2 2 VT OVEN DR NEON OVEN HIGH BROIL FAN LT SW MOTOR WH 16 LIMIT 3000WBR BROIL E3NO

OR BU NC

GA 1 GY J1 MOTOR WH J1 NEU AUX DLB-N BK BAKE

DOOR 6 TESMEPNESROARTURBEU E2 E1 E6 E9 NC 2800W LKSW LOCK PIN CIR 6 YL BAKE-E5 BU VT 2 WH/RD 5 DLB NO BU WH OR GY 1 PIN 65 432 4 ERC GENESIS/CONV BU

CIR OR 3 DLB E9

VT 2 E7 E4 E3 E5 E8

21 1 L1 MDL BR BA L2 L2 E8 GY 4 DLB-N E6

21 RD BU BR YL BK 14 16 16 16 6 5 4 3 21 GA BU WH BU WH GA GA GA OR GY VT VT RD WH

2 LEFT SOCKET CIR WH WH SURFACE RIGHT SURFACE VT NEON NEON NC BK 1b BAKE 16GA SPLICE OVEN HIGH 2b ELEMENT BU YL 2500W 1b 1b 1b 1a 2b 2b 2b 18 or 20GA LIMIT 14 RF 2a 1500W 2000W 1200W OVEN * 14 GA GN BROIL GA 1a 1a 1a LIGHT CHASSIS GROUND BR ELEMENT * RD RR 2a LR 2a LF 2a BU 14 BACKGUARD 16GA (NOTE 7) GROUND GA BK WH GROUND OR WH STRAP

NOTES: (L2) WHITE (L1) H1 H2 H1 H2 H1 H2 H1 H2 BLACK (N) RED 1. ALL INTERNAL WIRES ARE 18CGXAL, 1U5N0LESS OTHERWISE NOTED. SF2 IS SEW-2/SF2C20R0ATED. MAIN P L1 L2 P L1 L2 P L1 L2 P L1 L2 TERMINAL 2. ALL REPLACEMENT WIRES MUST HAVE SAME RATING AS ORIGINAL WIRE. BLOCK (NOTE 5) 3. SEE SERIAL PLATE FOR INPUT VOLTAGE/WATTAGE RATING. DIAGRAM * 4. DENOTES OPTIONAL EQUIPMENT AND RELATED WIRING( ) NOT SUPPLIED ON SOME MODELS. 5. ELEMENT WATTAGES VARY BY MODEL. REPLACEMENT ELEMENTS

MUST HAVE SAME WATTAGE AS ORIGINAL ELEMENTS. 6. GROUND STRAP NOT USED FOR FOUR WIRE INSTALLATIONS.

June 2003 WARNING – ELECTRICAL SHOCK HAZARD DANGER -RISQUE DE CHOC ELECTRIQUE RANGE CONDITIONS SHOWN: SCHEMATIC – DISCONNECT POWER AT MAIN -DEBRANCHER L’ALIMENTATION ELECTRIQUE. ELEMENTS OFF AND AT ROOM 35-32117101-0 AVANT D’ENTRETENIR CETTE UNITE. TEMPERATURE. FUSE OR CIRCUIT BREAKER BEFORE SERVICING. DOOR UNLATCHED AND CLOSED. FAILURE TO DO SO COULD RESULT IN SERIOUS LE MANQUE DE RESPECT DE CETTE CONSIGNE POURRAIT INJURY OR DEATH. AVOIR COMME RESULTAT UNE BLESSURE GRAVE OU MORTELLE.