tech-sheet-12728242
Wiring Diagram Bottom Mount Refrigerator Technical Information

! WARNING 596.73502202 596.73503202 596.73504202 596.73509202

To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before Due to a possibility of personal injury or property damage, always contact an authorized technician for servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires service or repair of this refrigerator. removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization. ! CAUTION See Note below about alternate wiring All safety information must be followed as provided in Service Manual. of Refrigerator door harness ! WARNING

To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before servicing unless testing is required. Discharge capacitors through a 10,000 ohm resistor before handling. Wires removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.

No-Load Performance, Controls in Normal Position

Kw/24 hr ±0.4 Percent Run Time Cycles/24 hr Refrigerator Center Freezer Compartment 65° 90° 110° ±10% ±25% .8 1.4 2.1 Compartment Average Food Temperature ±3°F Average Food Temperature ±3°F

Ambient °F 65° 90° 110° 65° 90° 110° 65° 90° 110° 65° 90° 110° 25 cu ft 30 45 70 27 24 18 38 40 42 0 0 0

Temperature Relationship Test Chart

Evaporator Evaporator Suction Line Average Total Suction Head Pressure ±7°F Wattage ±10% ± 5 PSIG Outlet Inlet Pressure ±3°F ±3°F ±2 PSIG

Ambient °F 65° 90° 65° 90° 65° 90° 65° 90° 65° 90° 65° 90° 25 cu ft -15 -14 -15 -14 65 95 135 140 0 1 83 135

Schematic

Note: In the event of excessive moisture on fresh food door mullion. The red and blue cabinet wires to door harness can be reversed to power fresh food door mullion heater continuously. This will help to reduce moisture on fresh food door mullion. See wiring alternate above for wiring in mullion heater for continuous operation.

December 2003 4 12728242 December 2003 1 12728242

Component Specifications Water Dispenser

! WARNING ! WARNING

To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization. removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.

Part Number Component Specifications all parts Seconds to dispense 10 oz. water 5/16″ 115VAC/60HZ unless noted Plastic Tubing C8931612 Compressor run capacitor 210/220 VAC Supply pressure 20 psig 35 psig 45 psig 55 psig 75 psig Routed Thru a 5/16″x5/16″O.D. Volt …………………………………………….. Filter model 10.4 8.0 7.0 6.0 5.0 Conduit Foamed in Compression Union Capacitance ………………………………… 15 µfd ± 10% Place Bypass installed Filter BTUH ………………………………………….. 905 BTUH Water Watt …………………………………………… Filter model 17.2 11.5 10.0 8.5 7.0 Dispenser Water Current Lock rotor…………………………. 60 Hz / 153 watts Reservoir 67003084 Compressor Current Full load …………………………… 19.0 amps± 15% New filter installed Remove Water Resistance Run windings ………………. 1.26 amps± 15% Tubing From Plastic Tubing Resistance Start windings ……………… 3.33 ohms± 15% A minimum supply pressure of 35 psig for water filter units. Conduit From 5/16″ O.D. 4.28 ohms± 15% Minimum pressure requirement ensures that water valves close and sufficient Dispenser End Settings water volume is available to fill icemaker. Proper fill is 140 cc. of water #1……………………………………………….. Closing temperatures in 7.5 seconds. Failure of water valves to close because of low pressure Ice #4……………………………………………….. 29.0°F will result in fill-tube freeze-up or dripping at cavity. Maker #7……………………………………………….. 23.0°F 67002738 Damper control 19.0°F Settings #1 – out……………………………………….. Temperatures Dispenser Water Temperature #4 – in…………………………………………. -0.6°F ±3° #4 – out……………………………………….. 10.0°F ±1.5° Water Usage 65°F Room 90°F Room #7 – out……………………………………….. -8.0°F ±1.5° 67001046 Freezer temperature control -17.9°F ±3° ounces Ambient Ambient Rotation (facing end opposite shaft) RPM Clockwise 8 40.2°F 42.1°F

Watt ……………………………………………. 1250 RPM 16 39.8°F 41.4°F Current………………………………………… 4.20 watts±15%@115VAC 63m amps± 15%@115VAC 24 42.5°F 45.0°F

32 45.9°F 51.1°F

R0131583 Condenser motor 40 50.6°F 57.2°F

38°- 40°F fresh food temperature after 12 hours stabilized in 1/4″ OD water reservoir. Water capacity of tank is 36.5 ounces. Plastic Tubing

WATER DISPENSING FLOW

67003636 Evaporator fan motor Rotation (facing end opposite shaft) Clockwise Adaptive Defrost Control (ADC) 12754901 67002783 Overload/Relay RPM…………………………………… 2800 RPM Watt……………………………………. 5.9 ±15% watts@115VAC 12001937 Thermostat (Defrost) The ADC adapts the compressor run time between defrosts to achieve optimum defrost intervals by monitoring the cold control and length the Ult. trip amps @ 158°F (70°C)………… 3.51 amps± 15% defrost heater is on. 67002493 Evaporator heater Close temperature ………………………. 142°F ±16°F After initial power up, defrost interval is 4 hours compressor run time. Defrost occurs immediately after the 4 hours. Open temperature ………………………. 230°F ±9°F 10 seconds ±5 Optimum defrost is 15 minutes. Each additional minute the defrost thermostat remains closed, 1 hr. is subtracted from the previous defrost Short time trip (seconds) ……………….. 13.9 amps ±2amps interval. Each minute the thermostat opens prior to optimum defrost, it extends the next defrost interval 1 hr. When in defrost if defrost terminator Short time trip (amps @77°F (25°C) .. opens there is a 6 minute drip time before compressor restarts or ADC will terminate defrost at 30 minutes even if defrost thermostat has not 120VAC opened and will reset the defrost interval to the 8 hr. minimum setting. Volt ……………………………………………. 490 watts Watt …………………………………………… 10amps 4 hours of continuous compressor run resets the next defrost interval to 8 hours and will initiate a defrost, if 8 hours of compressor run time has Current………………………………………… also occurred. Resistance across terminals: Open Power up: Refrigeration mode will occur unless both the cold control and defrost terminator are open, in that case the defrost mode will occur for Above 42°F ±5° ……………………………. Closed 2 minutes. Below 12°F ±7°…………………………….. 115 VAC To Force Defrost: Turn cold control on and off 3 times within 6 seconds. Volt …………………………………………….. 470 ±5% watts @ 115VAC A forced defrost is immediate without any delay regardless of the cold control state or the defrost terminator state. (When the ADC cycles the unit Wattage ………………………………………. into defrost on it’s own defrost it is delayed until 4 minutes after the compressor has been cycled off by the cold control.) Resistance…………………………………… 28 ±5% ohms Note: Cold control contacts must make and break for defrost to occur. In some cases freezer door must be left open to warm the cold control 12754901 Adaptive defrost control Volt…………………………………………….. 120VAC, 60 HZ sensing capillary up to get the cold control contact to make and break. If cold control contacts do not make and break unit will not force a defrost. 12544002 Water Valve (primary) See adaptive defrost board section 67003311 Water Valve (secondary) Watts …………………………………………. To Terminate Defrost: The only way to manually terminate defrost is to disconnect power to the unit. Unit will automatically come out of defrost C3680310 Light switch Brown side 35w Resistance .19 ohms at the end of the normal defrost cycle. Watts …………………………………………. Purple side 20w Resistance .26 ohms Input Voltage Readings and Checks Type…………………………………….. Brown side 35w Resistance .19 ohms L1 to L2 ……………………………………. Line voltage should be present when the unit is powered Volt……………………………………… Purple side 20w Resistance .26 ohms CC to L2 ……………………………………. Line voltage should be present when the cold control contacts are closed and ADC is not in defrost. Current………………………………….. STAT to L2……………………………………. Line voltage should be present when the ADC is in defrost mode and the defrost terminator contacts are SPST NC 125VAC closed 8 amps Output Voltage Readings and Checks 67002952(BLK) Mullion Assembly w/ Heater Volt……………………………………… 120 VAC HTR to L2………………………………….. Line voltage should be present when the ADC is in defrost mode 67002953(BSQ) Wattage ………………………………………. 10±.5 watts @ 120VAC COMP to L2 ………………………………….. Line voltage should be present when the ADC is not in the defrost mode. 67002954 (G) Resistance…………………………………… 1440 ±5% ohms 67002951 (W) Resistance checked at leads at center of hinged Type…………………………………….. side of Fresh Food door. 12466101 Light switch / Interlock Volt……………………………………… Current………………………………….. SPDT NO/NC 125VAC 8 amps

December 2003 2 12728242 December 2003 3 12728242