tech-sheet-12728235
Wiring Diagram Technical Information Bottom Mount Refrigerator

! WARNING Due to a possibility of personal injury or property damage, always contact an authorized technician for service or repair of this refrigerator. To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires ! CAUTION removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization. All safety information must be followed as provided in Service Manual 16021484.

! WARNING

To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before servicing unless testing is required. Discharge capacitors through a 10,000 ohm resistor before handling. Wires removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.

No-Load Performance, Controls in Normal Position

Kw/24 hr ±0.4 Percent Run Time Cycles/24 hr Refrigerator Center Freezer Compartment 65° 90° 110° ±10% ±25% .8 1.4 2.1 Compartment Average Food 65° 90° 110° 65° 90° 110° Temperature ±3°F Average Food Temperature ±3°F

Ambient °F 65° 90° 110° 65° 90° 110° 20 cu ft 25 40 60 30 27 22 38 40 42 0 0 0

Temperature Relationship Test Chart

Evaporator Evaporator Suction Line Average Total Suction Head Pressure ±7°F Wattage ±10% ± 5 PSIG Outlet Inlet Pressure ±3°F ±3°F ±2 PSIG

Ambient °F 65° 90° 65° 90° 65° 90° 65° 90° 65° 90° 65° 90° 20 cu ft -15 -14 -15 -14 65 95 135 140 0 1 83 135

Schematic

November 2002 4 12728235 November 2002 1 12728235

Component Specifications Water Dispenser

! WARNING ! WARNING

To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization. removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.

Component Specifications all parts Seconds to dispense 10 oz. water 5/16″ Plastic tubing 5/16″ x 5/16″ Compressor run capacitor 115VAC/60HZ unless noted routed thru conduit Compression nut Compressor 210/220 VAC Supply pressure 20 psig 35 psig 45 psig 55 psig 75 psig in this area Volt …………………………………………….. Filter model 10.4 8.0 7.0 6.0 5.0 Filter Damper control Capacitance ……………………………….. 15 µfd ± 10% Water Freezer temperature control Bypass installed Dispenser Water BTUH …………………………………………. 905 BTUH Remove Water Reservoir Condenser motor Watt …………………………………………… Filter model 17.2 11.5 10.0 8.5 7.0 tubing from conduit Evaporator fan motor Current Lock rotor ………………………… 60 Hz / 153 watts from dispenser end Plastic Tubing Overload/Relay Current Full load…………………………… 19.0 amps± 15% New filter installed 5/16″ O D Resistance Run windings………………. 1.26 amps± 15% Ice Thermostat (Defrost) Resistance Start windings……………… 3.33 ohms± 15% A minimum supply pressure of 35 psig for water filter units. Maker 4.28 ohms± 15% Minimum pressure requirement ensures that water valves close and sufficient Evaporator heater Settings water volume is available to fill icemaker. Proper fill is 140 cc. of water Defrost timer #1 ………………………………………………. Closing temperatures in 7.5 seconds. Failure of water valves to close because of low pressure Water Valve (primary) #4 ………………………………………………. 34.0°F will result in fill-tube freeze-up or dripping at cavity. #7 ………………………………………………. 27.0°F 20.0°F Dispenser Water Temperature Settings #1 – out ………………………………………. Temperatures Water Usage 65°F Room 90°F Room #4 – Differential ……………………………. -0.6°F ±3° #4 – out ………………………………………. 10.0°F ±1.5° ounces Ambient Ambient #7 – out ………………………………………. -8.0°F ±1.5° -17.9°F ±3° 8 40.2°F 42.1°F Rotation (facing end opposite shaft) RPM …………………………………………… Clockwise 16 39.8°F 41.4°F Watt ……………………………………………. Current ……………………………………….. 1100 RPM 24 42.5°F 45.0°F 8.0 watts±15%@115VAC 0.10 amps± 15%@115VAC 32 45.9°F 51.1°F

40 50.6°F 57.2°F

38°- 40°F fresh food temperature after 12 hours stabilized in Plastic Tubing water reservoir. Water capacity of tank is 36.5 ounces. 1/4″ O D

Replacing Damper Control WATER DISPENSING FLOW

Rotation (facing end opposite shaft) Clockwise 1. Remove lens cover by removing hex head screw in lens cover. Slide cover rearward and drop down to remove. RPM…………………………………… Watt……………………………………. 2800 RPM 5.9 ±15% watts@115VAC Ult. trip amps @ 158°F (70°C) ……….. Close temperature………………………. 3.51 amps± 15% Open temperature ………………………. 142°F ±6° Short time trip (seconds) ……………….. Short time trip (amps @77°F (25°C) .. 257°F ±3° 10 seconds ±5 14 amps ±2amps

Volt ……………………………………………. 120/240 VAC 2. Remove damper control cover and foam insert by pulling straight down on sides of rear cover and tilt forward Watt …………………………………………… 1000 watts approximately ½” to 1″. This will release the cover from the tabs holding it in place. Current ……………………………………….. 10/5 amps Resistance across terminals: FOAM INSERT Above 42°F ±5° ……………………………. Open Below 12°F ±7° ……………………………. Closed DAMPER CONTROL COVER

Volt …………………………………………….. 115 VAC 3. Release tension on damper control belt by squeezing tabs on bottom of belt tensioner to release tensioner Wattage………………………………………. 450 ±5% watts @ 115VAC from it’s holding tabs. Resistance ………………………………….. 29 ±5% ohms

Volt…………………………………………….. 120VAC, 60 HZ Defrost period (minutes)……………….. 33 ± 3.6 Defrost cycle (hours)…………………… 8

Watts …………………………………………. Brown side 35w, Purple side 20w

Water Valve (secondary) Watts …………………………………………. Brown side 35w, Purple side 20w

Light switch Type…………………………………….. SPST NC BELT TENSIONER Light switch / Interlock Volt……………………………………… 125/250 VAC Current………………………………….. 8 / 6 amps 4. Install new damper in reverse order. When installing belt align large slots on belt with large cogs on damper and control knob gear. This will synchronize control knob with damper control. Type…………………………………….. SPDT NO/NC Volt……………………………………… 125/250 VAC 5. Install belt tensioner on mounting tabs and turn counter clockwise to increase tension on belt. Current………………………………….. 8 / 6 amps 6. Reinstall damper control cover by hooking bottom on tabs and rotating up until it snaps into place. 7. Reinstall lens by sliding lens cover forward on tabs and installing hex head screw.

November 2002 2 12728235 November 2002 3 12728235