tech-sheet-12728231
Wiring Diagram Technical Information Bottom Mount Refrigerator

! WARNING 596.73502200 596.73503200 596.73504200 596.73509200

To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before Due to a possibility of personal injury or property damage, always contact an authorized technician for servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires service or repair of this refrigerator. removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization. ! CAUTION See Note below about alternate wiring All safety information must be followed as provided in Service Manual. of Refrigerator door harness ! WARNING

To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before servicing unless testing is required. Discharge capacitors through a 10,000 ohm resistor before handling. Wires removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.

No-Load Performance, Controls in Normal Position

Kw/24 hr ±0.4 Percent Run Time Cycles/24 hr Refrigerator Center Freezer Compartment 65° 90° 110° ±10% ±25% .8 1.4 2.1 Compartment Average Food 65° 90° 110° 65° 90° 110° Temperature ±3°F Average Food Temperature ±3°F

Ambient °F 65° 90° 110° 65° 90° 110° 25 cu ft 30 45 70 27 24 18 38 40 42 0 0 0

Temperature Relationship Test Chart

Evaporator Evaporator Suction Line Average Total Suction Head Pressure ±7°F Wattage ±10% ± 5 PSIG Outlet Inlet Pressure ±3°F ±3°F ±2 PSIG

Ambient °F 65° 90° 65° 90° 65° 90° 65° 90° 65° 90° 65° 90° 25 cu ft -15 -14 -15 -14 65 95 135 140 0 1 83 135

Schematic

Note: In the event of excessive moisture on fresh food door mullion. The red and blue cabinet wires to door harness can be reversed to power fresh food door mullion heater continuously. This will help to reduce moisture on fresh food door mullion. See wiring alternate above for wiring in mullion heater for continuous operation.

October 2002 4 12728231 October 2002 1 12728231

Component Specifications Water Dispenser

! WARNING ! WARNING

To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization. removed during disassembly must be replaced on correct terminals to ensure proper grounding and polarization.

Part Number Component Specifications all parts Seconds to dispense 10 oz. water 5/16″ 115VAC/60HZ unless noted Plastic Tubing C8931612 Compressor run capacitor 210/220 VAC Supply pressure 20 psig 35 psig 45 psig 55 psig 75 psig Routed Thru a 5/16″x5/16″O.D. Volt …………………………………………….. Filter model 10.4 8.0 7.0 6.0 5.0 Conduit Foamed in Compression Union Capacitance ……………………………….. 15 µfd ± 10% Place Bypass installed Filter BTUH …………………………………………. 905 BTUH Water Watt …………………………………………… Filter model 17.2 11.5 10.0 8.5 7.0 Dispenser Water Current Lock rotor ………………………… 60 Hz / 153 watts Reservoir 67002782 Compressor Current Full load ………………………….. 19.0 amps± 15% New filter installed Remove Water Resistance Run windings………………. 1.26 amps± 15% Tubing From Plastic Tubing Resistance Start windings……………… 3.33 ohms± 15% A minimum supply pressure of 35 psig for water filter units. Conduit From 5/16″ O.D. 4.28 ohms± 15% Minimum pressure requirement ensures that water valves close and sufficient Dispenser End Settings water volume is available to fill icemaker. Proper fill is 140 cc. of water #1 ………………………………………………. Closing temperatures in 7.5 seconds. Failure of water valves to close because of low pressure Ice #4 ………………………………………………. 29.0°F will result in fill-tube freeze-up or dripping at cavity. Maker #7 ………………………………………………. 23.0°F 67002738 Damper control 19.0°F Settings #1 – out ………………………………………. Temperatures Dispenser Water Temperature #4 – in ………………………………………… -0.6°F ±3° #4 – out ………………………………………. 10.0°F ±1.5° Water Usage 65°F Room 90°F Room #7 – out ………………………………………. -8.0°F ±1.5° -17.9°F ±3° ounces Ambient Ambient Rotation (facing end opposite shaft) 67001046 Freezer temperature control RPM Clockwise 8 40.2°F 42.1°F

Watt……………………………………………. 1250 RPM 16 39.8°F 41.4°F Current ……………………………………….. 4.20 watts±15%@115VAC 63m amps± 15%@115VAC 24 42.5°F 45.0°F

32 45.9°F 51.1°F

40 50.6°F 57.2°F

R0131583 Condenser motor 38°- 40°F fresh food temperature after 12 hours stabilized in 1/4″ OD water reservoir. Water capacity of tank is 36.5 ounces. Plastic Tubing

WATER DISPENSING FLOW

67002778 Evaporator fan motor Rotation (facing end opposite shaft) Clockwise Adaptive Defrost Control (ADC) 12566102 67002783 Overload/Relay RPM…………………………………… Watt……………………………………. 2940 RPM 4.0 ±15% watts@115VAC The ADC adapts the compressor run time between defrosts to achieve optimum defrost intervals by monitoring the cold control and length the Ult. trip amps @ 158°F (70°C) ……….. defrost heater is on. Close temperature ……………………… 3.51 amps± 15% After initial power up, defrost intervals are 6 hr.(initial), 8 hr.(minimum), 96 hr. (maximum). Defrost is delayed for 4 min. after the control cycles Open temperature………………………. compressor off. 142°F ±16°F Optimum defrost is 15 minutes. Each additional minute the defrost thermostat remains closed, 1 hr. is subtracted from the previous defrost interval. Short time trip (seconds)……………….. Each minute the thermostat opens prior to optimum defrost, it extends the next defrost interval 1 hr. ADC will terminate defrost at 30 minutes even Short time trip (amps @77°F (25°C).. 230°F ±9°F if defrost thermostat has not opened and will reset the defrost interval to the 8 hr. minimum setting. 10 seconds ±5 A 6 minute delay occurs after defrost thermostat opens before compressor is allowed to run. If defrost thermostat opens within 30 seconds of 13.9 amps ±2amps beginning of defrost, delay is by passed. Four hours of continuous compressor run will initiate a defrost, and defrost interval re-sets to 8 hours. 12001937 Thermostat (Defrost) Volt ……………………………………………. 120VAC Watt …………………………………………… 490 watts Power up: If defrost thermostat is open, compressor is powered. 67002493 Evaporator heater Current ……………………………………….. 10amps If defrost thermostat is closed, defrost is powered. Resistance across terminals: Above 42°F ±5°……………………………. Open To Force or Terminate defrost: Toggle fresh food door light switch 5 times within 6 sec. Below 12°F ±7° ……………………………. Closed Note: One of the fresh doors has to be closed to force or terminate defrost.

Volt …………………………………………….. 115 VAC If cold control is open, a forced defrost will not occur until the cold control closes, then the ADC will immediately switch the function to defrost. Wattage………………………………………. 470 ±5% watts @ 115VAC If cold control is closed and defrost terminator or heater circuit is open when defrost is forced, ADC shuts unit down momentarily and immediately Resistance ………………………………….. restores power to refrigeration circuit. 28 ±5% ohms If cold control is closed, a forced defrost is immediate without any delay (When the ADC cycles the unit into defrost on it’s own defrost it is delayed until 4 minutes after the compressor has been cycled off by the cold control.) 12566102 Adaptive defrost control Volt …………………………………………….. 120VAC, 60 HZ When ADC is in defrost, cold control is closed and refrigeration is forced, ADC bypasses 6 minute dwell time. 12544002 Water Valve (primary) See adaptive defrost board section 12544105 Water Valve (secondary) Input Voltage Readings and Checks C3680310 Light switch Watts …………………………………………. Brown side 35w Resistance .19 ohms E2 to E4 …………………………………………….Line voltage should be present when the unit is powered Purple side 20w Resistance .26 ohms E6 to E4 …………………………………………….Line voltage should be present when the cold control contacts are closed E5 to E4 …………………………………………….Line voltage should be present when the ADC is in defrost mode and the defrost terminator contacts are Watts …………………………………………. Brown side 35w Resistance .19 ohms Purple side 20w Resistance .26 ohms closed E7 to E4 ……………………………………………Line voltage should be present when the fresh food door is open (fresh food light switch closed) Type…………………………………….. SPST NC Volt……………………………………… 125VAC Output Voltage Readings and Checks Current………………………………….. 8 amps E1 to E4 ……………………………………………Line voltage should be present when the ADC is in defrost mode E3 to E4 ……………………………………………Line voltage should be present when the ADC is not in the defrost mode or compressor dwell mode 67002717(BLK) Mullion Assembly w/ Heater Volt……………………………………… 120 VAC 67002718(BSQ) Wattage………………………………………. 10±.5 watts @ 120VAC 67002719 (G) Resistance ………………………………….. 1440 ±5% ohms 67002720 (W) Resistance checked at leads at center of hinged Type…………………………………….. 12466101 Light switch / Interlock Volt……………………………………… side of Fresh Food door. Current………………………………….. SPDT NO/NC

125VAC

8 amps

October 2002 2 12728231 October 2002 3 12728231