tech-sheet-12728213
Wiring Diagram Technical Information Bottom Mount Refrigerator

! WARNING Due to a possibility of personal injury or property damage, always contact an authorized technician for service or repair of this refrigerator. To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires ! CAUTION removed during disassembly must be replaced on correct terminals to ensure proper earthing and polarization. All safety information must be followed as provided in Service Manual 16021685.

! WARNING

To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before servicing unless testing is required. Discharge capacitors through a 10,000 ohm resistor before handling. Wires removed during disassembly must be replaced on correct terminals to ensure proper earthing and polarization.

No-Load Performance, Controls in Normal Position

Kw/24 hr ±0.4 Percent Run Time Cycles/24 hr Refrigerator Center Freezer Compartment ±10% ±25% 18° 32° 43° Compartment Average Food .9 1.5 2.1 18° 32° 43° 18° 32° 43° Temperature ±3°C .9 1.4 2.0 Average Food .9 1.4 2.0 Temperature ±3°C

Ambient °C 18° 32° 43° 18° 32° 43° 623 Litre 538 Litre 25 40 90 30 27 22 2 4 5 -20 -20 -20 566 Litre 25 40 90 33 30 24 2 4 5 -20 -20 -20

25 40 90 33 30 24 2 4 5 -20 -20 -20

Temperature Relationship Test Chart

Evaporator Evaporator Suction Line Average Total Suction Head ±7°C Wattage ±10% Outlet Inlet Pressure Pressure ±3°C ±3°C ±2 Bar ± 5 Bar

Ambient °C 18° 32° 18° 32° 18° 32° 18° 32° 18° 32° 18° 32° 623 Litre 538 Litre -28 -28 -28 -28 20 34 135 155 0.5 0.8 3 5 566 Litre -28 -28 -28 -28 20 34 135 155 0.5 0.8 3 5

-28 -28 -28 -28 20 34 135 155 0.5 0.8 3 5

Schematic

May 2002 4 12728213 May 2002 1 12728213

Component Specifications Damper Replacement

! WARNING ! WARNING

To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before To avoid risk of electrical shock that can cause death or severe personal injury, disconnect unit from power before servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires servicing unless tests require power. Discharge capacitors through a 10,000-ohm resistor before handling. Wires removed during disassembly must be replaced on correct terminals to ensure proper earthing and polarization. removed during disassembly must be replaced on correct terminals to ensure proper earthing and polarization.

Part Number Component Specifications all parts 420 VAC Replacing Damper Control 10958304 Compressor run capacitor 240VAC/50HZ unless noted 12049719 Compressor 5 µfd ± 5% 1. Remove lens cover by removing hex head screw in lens cover. Slide cover rearward and drop down to remove. Volt …………………………………………….. 12571702 Damper control Capacitance ……………………………….. 940 BTUH 2. Remove damper control cover and foam insert by pulling straight down on sides of rear cover and tilt forward 67001046 Freezer temperature control approximately ½” to 1″. This will release the cover from the tabs holding it in place. BTUH …………………………………………. 50 Hz / 168 watts 10884508 Condenser motor Watt …………………………………………… 12 amps± 15% FOAM INSERT 10449509 Evaporator fan motor Current Lock rotor ………………………… .79 amps± 15% 12555903 Overload/Relay Current Full load ………………………….. 11.4 ohms± 15% DAMPER CONTROL COVER Resistance Run windings………………. 18.61ohms±15% 12001937 Thermostat (Defrost) Resistance Start windings……………… 3. Release tension on damper control belt by squeezing tabs on bottom of belt tensioner to release tensioner Closing temperatures from it’s holding tabs. 12225802 Evaporator heater Settings 1.1°C 12566302 Defrost timer #1 ………………………………………………. -2.8°C BELT TENSIONER C3680310 Light switch #4 ………………………………………………. -6.6°C 12466101 Light switch / Interlock #7 ………………………………………………. 4. Damper can be removed by pushing in tabs on left and right side of damper control to release damper from Temperatures rear wall. Settings -18.1°C ±3° #1 – out ………………………………………. -12.2°C ±1.5° #4 – in ………………………………………… -22.2°C ±1.5° #4 – out ………………………………………. -27.7°C ±3° #7 – out ………………………………………. Clockwise Rotation (facing end opposite shaft) RPM …………………………………………… 1300 RPM Watt……………………………………………. 10.7 watts±15%@ 230VAC Current ……………………………………….. .06 amps± 15%@ 230VAC

Rotation (facing end opposite shaft) Clockwise

RPM…………………………………… 2700 RPM Watt……………………………………. 8.4 ±15% watts @ 230VAC

Ult. trip amps @ 158°F (70°C) ……….. 1.56 amps± 15% Close temperature ……………………… Open temperature………………………. 61°C ±6°

Short time trip (seconds)……………….. 120°C ±3° Short time trip (amps @77°F (25°C).. 10 seconds ±5 6.8 amps ±2amps

Volt ……………………………………………. 120/240 VAC Watt …………………………………………… 1000 watts Current ……………………………………….. 10/5 amps Resistance across terminals: Above 5.5°C ±5° ………………………….. Open Below –11.1°C ±7°……………………….. Closed

Volt …………………………………………….. 230 VAC Wattage………………………………………. Resistance ………………………………….. 395 ±5% watts @ 230VAC 29 ±5% ohms

Volt…………………………………………….. 220-240VAC, 50 HZ Defrost period (minutes)……………….. 28 ± 3.6 Defrost cycle (hours)…………………… 8.4

Type…………………………………….. SPST NC Volt……………………………………… 125/250 VAC Current………………………………….. 8 / 6 amps

Type…………………………………….. SPDT NO/NC Volt……………………………………… 125/250 VAC Current………………………………….. 8 / 6 amps

RELEASE TABS

5. Install new damper in reverse order. When installing belt align large slots on belt with large cogs on damper and control knob gear. This will synchronize control knob with damper control.

6. Install belt tensioner on mounting tabs and turn counter clockwise to increase tension on belt. 7. Reinstall damper control cover by hooking bottom on tabs and rotating up until it snaps into place. 8. Reinstall lens by sliding lens cover forward on tabs and installing hex head screw.

May 2002 2 12728213 May 2002 3 12728213